Gas and Liquid sorting

[cpy]

So I have gas and liquid pumps but they suck everything up. How do I sort contaminated water so it can be routed to be cleaned? Same for air hydrogen -> generator and rest of air -> vent. Maybe venting contaminated air to filter room. You know advanced stuff!

[Masterpintsman]

There are water and gas filters that can be configured to split one material (they'll output it on the red connector) from a pipe/vent.

[heckubis]

be careful how you place filters though either one break the middle piece of old vent before adding the filter or you will create a loop that will allow half of the contents to proceed along the old pipeline anyway and not even touch the filter

on  side note if you making a long line of filters for several types of gas leaving this loop on the will prevent the filter from blocking the flow for other filters giving you complex options of gas management with power switches

[cpy]

Thanks! I needed that. Now to find out what is making so much CO2.

[Saturnus]

5 hours ago, cpy said:

Thanks! I needed that. Now to find out what is making so much CO2.

Main source of CO2 is coal generators and your dupes, especially if they're running on hamster wheel they produce a fairly large amount of CO2.

[BrightyBright]

any one can tell me how to deal with ''pump is not active'' or '' pump is not pumping'' and at vent is said'' overpressuried

[sai05]

sory for interup what magma can do ? and what we can do with magma ?

[Octyabr]

2 hours ago, BrightyBright said:

any one can tell me how to deal with ''pump is not active'' or '' pump is not pumping'' and at vent is said'' overpressuried

"pump not active" is when the pump is not powered. (I guess)

"pump not pumping" occurs when the pipe is filled and the pump cannot add more.

And vents over pressurised occurs when liquid vents are under the water, and gas vents when the pressure around them is above 2kg per tile. (even though the internal pressure can be up to 10kg per tile.)

2 hours ago, sai05 said:

sory for interup what magma can do ? and what we can do with magma ?

Magma can be used to boil water (as is commonly at 1500ºC) and once it cools down it becomes igneous rock. (very hot rock that you can use to build a furnace.)

[sai05]

i read some where in here there methode trune Contaminate O2  trun into normal water ? i use 9 Ac but nothing heppend

did you know ? 

Just now, Octyabr said:

"pump not active" is when the pump is not powered. (I guess)

"pump not pumping" occurs when the pipe is filled and the pump cannot add more.

And vents over pressurised occurs when liquid vents are under the water, and gas vents when the pressure around them is above 2kg per tile. (even though the internal pressure can be up to 10kg per tile.)

Magma can be used to boil water (as is commonly at 1500ºC) and once it cools down it becomes igneous rock. (very hot rock that you can use to build a furnace.)

 

[Octyabr]

Just now, sai05 said:

i read some where in here there methode trune Contaminate O2  trun into normal water ? i use 9 Ac but nothing heppend

did you know ? 

If you meant turn Contaminated water into clean water, then what you can do is heat contaminated water enough to turn it into steam (above 100ºC) and cool the steam below 100ºC There are many methods to make this, personally I pour contaminated water in magma to make it boil, then transport the steam (with a gas pump) to a cold area where it turns back into liquid and then transport the liquid to a template area because the cold area is below -30ºC and too much time there and the water turns into ice.

If you meant turn Contaminated oxygen into normal oxygen then you can cool it down using thermo regulators (air conditioners) to cool it down below -183ºC (you must use 16~17 of them chained or make a loop if you use less) If the gas is below that temperature, it will turn into liquid once it exits the gas vent, try to put the vent on top of something hot like batteries and away of your plants.

[HarryWang]

The contaminated water steam becomes water but where are going the contaminated material ? I don't understand and it make me sick

Thanks

[sai05]

5 hours ago, Octyabr said:

If you meant turn Contaminated water into clean water, then what you can do is heat contaminated water enough to turn it into steam (above 100ºC) and cool the steam below 100ºC There are many methods to make this, personally I pour contaminated water in magma to make it boil, then transport the steam (with a gas pump) to a cold area where it turns back into liquid and then transport the liquid to a template area because the cold area is below -30ºC and too much time there and the water turns into ice.

If you meant turn Contaminated oxygen into normal oxygen then you can cool it down using thermo regulators (air conditioners) to cool it down below -183ºC (you must use 16~17 of them chained or make a loop if you use less) If the gas is below that temperature, it will turn into liquid once it exits the gas vent, try to put the vent on top of something hot like batteries and away of your plants.

oh i made id trun into oxygen liquid then ? oxgen liquid use for ? will evaporate it self ?